{"product_id":"exo-terra-light-bracket","title":"Exo Terra Light Bracket","description":"\u003cdiv class=\"et_pb_module et_pb_text et_pb_text_3_tb_body  et_pb_text_align_left et_pb_bg_layout_light\"\u003e\n\u003cdiv class=\"et_pb_text_inner\"\u003e\n\u003ch4\u003eLight Dome Support Bracket\u003c\/h4\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"et_pb_module et_pb_wc_description et_pb_wc_description_0_tb_body et_pb_bg_layout_light  et_pb_text_align_left\"\u003e\n\u003cdiv class=\"et_pb_module_inner\"\u003e\n\u003cul\u003e\n\u003cli\u003eSuspension bracket for Light Dome, Reptile Dome or Wire Light\u003c\/li\u003e\n\u003cli\u003eEasily adjustable\u003c\/li\u003e\n\u003cli\u003eExtends life span of light bulbs\u003c\/li\u003e\n\u003cli\u003eSuspends light fixtures securely\u003c\/li\u003e\n\u003cli\u003eHelps prevent accidental tipping\u003c\/li\u003e\n\u003cli\u003ePrevents terrarium damage\u003c\/li\u003e\n\u003cli\u003eWith self-adhesive support base\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"et_pb_module et_pb_wc_description et_pb_wc_description_1_tb_body et_pb_bg_layout_light  et_pb_text_align_left\"\u003e\n\u003cdiv class=\"et_pb_module_inner\"\u003e\n\u003cp\u003eThe Exo Terra Light Bracket is designed to securely suspend a Dome or Wire fixture above an Exo Terra Natural Terrarium or any other glass terrarium. The Exo Terra Light Bracket easily adjusts in height to fit most types of fixtures or to regulate heat\/light according to the required terrarium conditions. Once the Bracket and fixture are installed, lightbulbs (like basking lamps, Solar Glo, etc….) will no longer be exposed to movement, resulting in a drastically improved lifespan.\u003c\/p\u003e\n\u003cp\u003eInstallation and usage:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eGlass surface preparation: surface temperature for application should be no lower than 60°F degrees (16°C) and not higher than 85°F degrees (29°C). If climate will not permit, move unit to appropriate conditions. Area to receive tape should first be thoroughly cleaned with a liquid detergent and warm water solution. Rinse with clean water and dry completely. A final wipe with 50\/50 alcohol\/water is highly recommended for best results (use a clean, lint-free cloth). Ensure surface is dry and residue free before proceeding. Note: The position of the adhesive support base cannot be changed after it has been affixed.\u003c\/li\u003e\n\u003cli\u003eLoosen the screw at the back of the adhesive support base and remove the Light Bracket from the adhesive support base.\u003c\/li\u003e\n\u003cli\u003eWith the protective backing still intact, place the adhesive support base on the back or the side of the terrarium to determine its final position and mark the position with a wax pencil or other marker.\u003c\/li\u003e\n\u003cli\u003eRemove the protective backing and carefully fit the adhesive support base within the marked area.\u003c\/li\u003e\n\u003cli\u003ePress the adhesive tape firmly and evenly against the glass panel, while gently twisting, to ensure proper adhesion. Make sure no air bubbles are showing. Let the Light Bracket rest on the terrarium mesh for 24 hours to allow the tape bond to cure properly before the dome is suspended and the weight of the dome can exert pressure on the adhesive support base. Once in place, the adhesive support base should not be removed!\u003c\/li\u003e\n\u003cli\u003eAllow the adhesive tape bond to cure for 24 hours before inserting the bracket in the adhesive support base or suspending any fixture on the bracket.\u003c\/li\u003e\n\u003cli\u003eAfter 24 hours, insert the bracket in the adhesive support base, adjust to the desired height and tighten the screw.\u003c\/li\u003e\n\u003cli\u003eRemove the first rubber washer, slide the ring of the fixture’s support over the rod of the Light Bracket, then replace the first rubber to secure the fixture’s support tightly in between both rubber stoppers.\u003c\/li\u003e\n\u003cli\u003eAdjust the position of the fixture by moving the rubber washers.\u003c\/li\u003e\n\u003cli\u003eAdjust the height and tighten the screw of adhesive supporting base when the Dome Fixture is suspended above the terrarium at the desired height.\u003c\/li\u003e\n\u003cli\u003eEnsure that the light’s focal point is not positioned above any plastic parts of the terrarium or screen cover to prevent damage.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eINSTALL LIGHT AFTER 24 HOURS TO ALLOW THE TAPE BOND TO CURE PROPERLY\u003c\/p\u003e\n\u003cp\u003eNOTE : FAILURE OF PROPER TAPE BONDING MAY BE ATTRIBUTED TO ONE OF FOUR ISSUES:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePoor surface preparation and\/or application.\u003c\/li\u003e\n\u003cli\u003ePoor adhesive contact: exposed adhesive side of tape being touched or contaminated.\u003c\/li\u003e\n\u003cli\u003eInsufficient pressure being applied.\u003c\/li\u003e\n\u003cli\u003eLamp hung too soon, tape not fully cured.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Hagen","offers":[{"title":"Default Title","offer_id":48263556301059,"sku":null,"price":25.99,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0663\/7292\/7747\/files\/PT2223_02.webp?v=1779836024","url":"https:\/\/thebeastiary.ca\/products\/exo-terra-light-bracket","provider":"The Beastiary","version":"1.0","type":"link"}